Fiberglass Body Accessories | Hood & Dash Accessories | Seating


Bubble Side Panels	Flat Side Panels
$242.00 a pair	$191.78 a pair

Give your fiberglass buggy a finished look with our bubble or flat side panels.

The bubble side panels are contoured to match the wrap over edge of our Nostalgia body or an original Meyer's Manx.

Due to the subtle differences in many bodies and the difficulty in accurately measuring contours, there is no way for us to know if our bubble side panels will fit other fiberglass bodies, without actually holding them up to the body.

The flat side panels were made for our Citation body, but they can be trimmed to fit most any body made for a stock Beetle pan that has been shortened 14 1/2".

Both styles are available in the same 16 beautiful gel-coat colors as our fiberglass bodies.

It is very difficult to adequately display colors on the web due to differences in monitors. Our gel-coat supplier does have an online color chart & we've provided a link to it below, but you should be aware that the colors appear darker than they actually are.

The Valspar website displays more colors than we normaly use & we do not always refer to them by the same name, but I've listed their color numbers with the color names we use below.

White	5W-1	Black	N/A
Canary Yellow	5L-27	Golden Yellow	5L-55
Lime Green	5G-28	Forest Green	5G-51
Aqua	5A-18	Med. Blue	5A-16
Dark Blue	5A-17	Teal	5A-19
Orange	5N-12	Bubble Gum Pink	5R-24
Red	5R-14	Maroon	5R-15
Purple	5R-44	Boysenberry	5R-26

Any of the above colors are available at no additional charge.

Other Valspar colors can be special ordered, but there may be an extra charge.

In order to guarantee color match, all fiberglass needs to be ordered at the same time.

4-Passenger Hardtop above shown in red with optional windows and chrome jiffy trim.

Expand your buggying season with our 4-Passenger hardtop.

$ 46.19 oval rear window w/hardware - not installed

$132.43 pair of 6" porthole side windows installed

$ 72.43 pair of 6" porthole side windows w/hardware - not installed

Fits the Nostalgia and Citation bodies as well as an original Manx.

Due to the subtle differences in many bodies and the difficulty in accurately measuring contours, there is no way for us to know if our top will fit other fiberglass bodies, without actually setting a top on the body.

Available in the same 16 beautiful gel-coat colors as our fiberglass bodies.

The Valspar website displays more colors than we normaly use & we do not always refer to them by the same name, but I've listed their color numbers with the color names we use below.

White	5W-1	Black	N/A
Canary Yellow	5L-27	Golden Yellow	5L-55
Lime Green	5G-28	Forest Green	5G-51
Aqua	5A-18	Med. Blue	5A-16
Dark Blue	5A-17	Teal	5A-19
Orange	5N-12	Bubble Gum Pink	5R-24
Red	5R-14	Maroon	5R-15
Purple	5R-44	Boysenberry	5R-26

Any of the above colors are available at no additional charge.

Other Valspar colors can be special ordered, but there may be an extra charge.

In order to guarantee color match, all fiberglass needs to be ordered at the same time.

This rubber based trim gives a finished look to the rough edge of any fiberglass body & helps protect against chipping. It's available in either plain black or black with a chrome accent strip.

Fiberglass products vary in thickness & in order for the metal core of jiffy trim to grip properly, the edge it's being installed on needs to be between 1/8" & 3/16" thick. This generally means that quite a bit of grinding is required before the trim can be installed.

If you order a body or hardtop from us, you can have us install the trim for you. The labor fee to prep the body & install the trim is:

Approximately footage requirements for our fiberglass products:

The custom molded rubber design of this gasket provides a water-tight seal. Normally installs between VW belly pan and body, but can be useful in other applications because of it's cushion design. Packaged in 19' length for complete installation.